Forum Replies Created
-
Posts
-
Hey Sean,
now it works – but on a different pc. I installed Windows on the PC I used earlier. I tested the USB 3 Ports which are directly on the mainboard. Then I installed the Kinect Software and it showed, that my USB Controller isn’t compatible with the Kinect.
So I installed Linux Mint on an old Laptop with USB 3 but – (this is the reason I didn’t use this pc in the first place) much weaker graphics… But it worked!
Do you think there is any way to get it working on the old pc? Maybe with a USB 3 PCI Card?I really appreciate your help!
I’ll share a photo of my sandbox when it’s finished!
This is a version where I removed unnecessary USB Devices:
andreas@sandbox-pc:~$ lsusb -t /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M |__ Port 2: Dev 3, If 0, Class=Vendor Specific Class, Driver=, 5000M |__ Port 2: Dev 3, If 1, Class=Vendor Specific Class, Driver=, 5000M |__ Port 2: Dev 3, If 2, Class=Audio, Driver=snd-usb-audio, 5000M |__ Port 2: Dev 3, If 3, Class=Audio, Driver=snd-usb-audio, 5000M /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/2p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M |__ Port 4: Dev 3, If 0, Class=Hub, Driver=hub/3p, 480M |__ Port 2: Dev 4, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M |__ Port 2: Dev 4, If 1, Class=Human Interface Device, Driver=usbhid, 1.5MI now tried it, here’s the output:
andreas@sandbox-pc:~/src/SARndbox-2.8$ lsusb -t /: Bus 09.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M |__ Port 1: Dev 2, If 0, Class=Vendor Specific Class, Driver=, 5000M |__ Port 1: Dev 2, If 1, Class=Vendor Specific Class, Driver=, 5000M |__ Port 1: Dev 2, If 2, Class=Audio, Driver=snd-usb-audio, 5000M |__ Port 1: Dev 2, If 3, Class=Audio, Driver=snd-usb-audio, 5000M /: Bus 08.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 480M /: Bus 07.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/2p, 12M /: Bus 06.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 05.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 04.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M /: Bus 03.Port 1: Dev 1, Class=root_hub, Driver=ohci-pci/3p, 12M |__ Port 1: Dev 2, If 0, Class=Human Interface Device, Driver=usbhid, 12M |__ Port 1: Dev 2, If 1, Class=Human Interface Device, Driver=usbhid, 12M /: Bus 02.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M /: Bus 01.Port 1: Dev 1, Class=root_hub, Driver=ehci-pci/6p, 480M |__ Port 2: Dev 3, If 0, Class=Mass Storage, Driver=usb-storage, 480M |__ Port 4: Dev 4, If 0, Class=Hub, Driver=hub/3p, 480M |__ Port 2: Dev 5, If 0, Class=Human Interface Device, Driver=usbhid, 1.5M |__ Port 2: Dev 5, If 1, Class=Human Interface Device, Driver=usbhid, 1.5MHello Sean,
thank you, for your help!
Yes “mint-pc” is an actual pc with fairly old hardware but with USB-3.
It runs a fresh install of Mint 19.3.
My Kinect is a modified Kinect, I soldered cables for the power supply directly to it’s board following this Tutorial and then used a USB-3 Type B Cable to connect it to the PC.I really appreciate your help!
Andreas
